I'm in the process of replacing wear ring and possibly impeller. I'd appreciate any comments on sealing around ride plate to help with cavitation.
Also, at what point should I consider replacing impeller? I can already see it's a bit nicked up.
I have reviewed the how-to thread on repairing the wear ring on the M2 jet with JB Weld, and have a few questions.
Does the JB Weld repair just last a season, and needs to be reapplied each year?
Has anyone tried to use some thing like HTS2000 ( www.aluminumrepair.com ) to fill in the...
Hello Sea-Doo community,
Can rocks do this kind of damage to a wear ring? It look more like the prop blades made this carving than rocks jammed in ?
We had the blue one original wear ring for 3 years... it was replaced by BRP current inventory that seems thinner and 1/8" longer... Suspecting...
Hi Guys,
My RXT-X 2011 recently started not to run that fast in the low RPM's, it is something like your car on ice...it takes time till start running as it has to. I took a picture of the impeller and wear ring and need some advice if they (Wear ring and impeller) need t be replaced.
Here...
So i just got done rebuilding my jet pump, everything except the impeller and the shaft it screws onto. After i finished i spun the impeller and noticed that i grazes the wear ring in 1 maybe 2 spots up near the edge of the wear ring. You can feel the hesitation when it gets to that spot or...
Hi all,
I have just bought a brand new seadoo gtr215 and took it out for the first time this weekend.
It ran fantastic all day until my last run. I was in neutral and went to take off when it started to vibrate and was quite loud. It didn't seem to have performance affected but in saying...
I have an RXT 260is that recently had a problem where the intake was completely clogged with junk that got sucked up due to getting to close to some reeds etc. (had no choice as I was in a no wake narrow channel and several sheriff boats came flying through the channel at full speed, lights...
OK I looked at the forums and did not find anything talking about this particular issue. I have a 96 seadoo GTI and have replaced the wear ring. I was lucky and did not have to remove the impeller to do so. The impeller and shaft turn free and has clearance in the new wear ring. When I attach...
Hi all, I've been a lurker on this page for quite some time and have pulled some really valuable information from you wonderful people.
My question i feel is unique mainly because i haven't seen this happen to anybody else when i searched. I own a 2007 Sea-Doo GTI SE 155 and have changed...
Hi everyone. i bought an 05' challenger 180 4tec boat this past february from a guy on facebook. needless to say, the wear ring and impeller were " not in bad shape" but still need to be replaced. i took the boat out on my 1st ever lake ride. ive never owned a boat before. but this little boat...
I have a 1996 GTX. It started to cavitate a little during a standstill hole shot. So I figured it was time to pull the pump. I pulled the pump and found the wear ring in pretty decent shape but the prop was quite chewed. It had a bent blade some good dents and a lot of leading edge damage. I...
This post is a follow up from the original post from some time ago. I have been busy. search my earlier post as it was closed.
I replaced the MPEM, No joy. BTW have one for sale. PM me if interested.
Replaced the voltage regulator, again No joy.
Replaced the sensor a third time and No...
Full instructions for wear ring replacement on Sea-Doo 4-Tec watercraft. Performed on a 2012 GTR 215 with iBR (intelligent Brake and Reverse), this video takes you step by step through the process.
If you like our videos, please subscribe!
http://youtu.be/axU-9Wi_Y-E
I have a 98 spx. I bought this boat a few months back and when riding, noticed that the trim would only go up between 1/2 to 3/4 on the gauge. I could tell it wasn't just the gauge due to the way it handled. I have a 97 spx that does not have this problem. I adjusted the small rod where the trim...
how do you know when the wear ring needs to be replace? Little rock got stocked in it.while was in the water, accelerate it , but didn't go. So at home i got the rock out , and it looks that nothing is broken
But the wear ring has some scratches. How do i know if it need to be replace? Thank you
Been having issues with cavitation on start with this boat. I got a Solas Impeller as a replacement and will put that in today. Before I put it in the pump, I wanted some opinion on the existing wearing.
I think I maybe ok. It has some groves in it and it still does fit tight.
Here...
I finally started taking apart my jet pump. The wear ring is shot and the impeller shows signs of abuse as well. I need to replace the impeller, a wear ring, and a couple of broken bolts (stator bolt being one of them sigh).
I have a couple of questions based on my pictures below:
1. Is there...
I just got a 2005 RXT with around 85 hours. I did a test ride before I bought it and was able to get it up to around 50-55 mph riding by myself. I thought it probably just needed a tune up because it had been sitting up for a little while according to the previous owner. A few days later I took...
My buddy and I are trying to remove our wear rings and carbon rings to fix some cavitation issues that we've had the past couple of years. (actually found a rock the size of a golf ball in the impelller so thinking that might help a good bit too). So we've got the wear rings under control, but...