pump

My pump support is cracked and needs to be replaced so that I can mount a new intake grate on it. I cannot find the exact replacement Pump Support (271000954)for my 99 GSXL but there is one on eBay from a 98 GSXL (271000866). The seller also has the part number of mine as interchangeable but in...

So I have a 2005 RXT 215 and I've been chasing an issue for the past 2 years. I get about 35 seconds into a WOT run and then hear a large squeal and loss of power. I pull the power and reset then turn it back on and then I startup like nothing had an issue. I recently had a oil cooler fail and...

just boughht this machine, looks great even sounds greta....it has no impeller or pump ass3embly, just drive shaft. my question is what years and makes are interchangeable, recommend new or used, where best place for new or used lol....its a 4strokes injection. i have a liceneced auto repair and...

I have a dumb question. Does my 2000 Millennium GTX (not DI) have an electric fuel pump in the tank. If so can the pump alone be replaced. I know it has the fuel pump sending unit in the tank, but is there a replaceable pump in there? Or do I need to replace the whole unit on this one. It...

Need a high pressure pump for 2001 SeaDoo Utopia 205 with a Mercury sportjet M2 EFI engine. Anyone know where I can find this pump? According to my mechanic, Mercury has discontinued this pump and there are no alternatives available. Anyone know of a pump for sale or an alternative that can be...

Designed and made my own since they are non existent nowadays. Seadoo 140mm (2,3 or 3.5) degree wedge | eBay

I am the original owner of a 2004 Utopia 205 with the 250hp Optimax. The pump has been cavitating for quite a while and pulling skiers is a challenge (not a lot of torq and lots of cavitation). I suspect that it's time for a rebuild. Doing a bit of research, there is not a replaceable wear...

Hi!! I charger my battery and after the charger is full, i start the engine and Works about 30 seconds and turnoff. In next day, when i tray to start, all is normal, pump, panel, beeps, no erros displaying, but when i try to start, nothing occours! Just the pump starts. The fuses and relays...

I was working in the engine compartment and leaned up against something and heard a pop. Much to my dismay I broke off a fuel barb fitting. How bad it this going to be? Do I have to replace the whole fuel pump or anyone know how to repair this. I think it's a fuel vent line but not certain...

Hey guys this is my first post. I just started redoing my seats so I'm trying to do as much as economically possible.… Well I'll start with a replacement porta potty, cooler, gps, radio and speakers(I did buy a clarion CMD8)side curtains(if possibly), fresh water pump, bilge pump, rocker switch...

Hi,any help advice would be greatly appreciated,recently purchased a 2002 seadoo gtx with 95hr on clock, took ski out and noticed it smoking at idle this is same on hose however with throttle on water this clears up,any ideas of what is causing this issue,also i have an issue were im finding...

Hi all, Over the winter I've been doing a few hours on my ski where I've had the time. Swapped the plastic 140mm for a bronze version. New bearings, seals etc. Holds 10psi for 10mins :) Installed it with all new drive line components, aligned the engine, and water tested it today and...

Hi folks, I've got a 99 GTI which has a leaky 140mm pump. It's a slow leak, and oddly oil will drain, but it won't fill with water. I've pressure tested it and it won't hold 10 psi for longer than a few minutes. I'm going to be using the ski well into the colder months on one of our local...

I got my ski running great now after a mess with a carb rebuild, I had one of the little hinge pins from the needle arm not correctly in its slot and it was causing a leak. It's just A Bit rich on oil though. When you set the oil pump lines, where should the throttle position be? I set the lines...

Im parting out a 96 gtx 787. Ski ate a piston so no piston or crank. Everything else good, except hull. All electronics work, pump good, could use a new wear ring. Everything must go,, super cheap, make offers. Ive gotta get it out of my garage to start a new project. Will clean up parts and...

I have a 2012 Challenger 210 SE 430. Its a great boat and we have used it a lot. It has been used in salt and fresh water but a decent amount in both, about 150 hours combined. I am having an issue with corrosion on the reverse gate and reverse support. There is also some corrosion on the bottom...

I had some cavitation so I pulled my pump and found the ring and prop pretty dinged up. It spins freely but it makes a little of a scraping noise when spinning. Is this normal? the machine has 55 hours on it and had a pump oil change about 10 hours ago. I'm going to change the impeller out so I...

OK, everybody knows this. I got lazy and did not run a hose or put it in the water. I figured I would run it about 30 seconds and shut it off. I needed to check something after a fix. So I fired up the engine, ran it at partial throttle and on shut down it gave a very unsatisfying glurg...

I have two problems. One, I cannot figure out how to remove the existing Bilge pump. Secondly, I can't find an OEM replacement. 1) I tried to remove my bilge pump but can't figure out how. Do I turn the big "wing nut" looking assembly at the top? So far, that will only move about 5 degrees...

I finally started taking apart my jet pump. The wear ring is shot and the impeller shows signs of abuse as well. I need to replace the impeller, a wear ring, and a couple of broken bolts (stator bolt being one of them sigh). I have a couple of questions based on my pictures below: 1. Is there...