pump

Im parting out a 96 gtx 787. Ski ate a piston so no piston or crank. Everything else good, except hull. All electronics work, pump good, could use a new wear ring. Everything must go,, super cheap, make offers. Ive gotta get it out of my garage to start a new project. Will clean up parts and...

I have a 2012 Challenger 210 SE 430. Its a great boat and we have used it a lot. It has been used in salt and fresh water but a decent amount in both, about 150 hours combined. I am having an issue with corrosion on the reverse gate and reverse support. There is also some corrosion on the bottom...

I had some cavitation so I pulled my pump and found the ring and prop pretty dinged up. It spins freely but it makes a little of a scraping noise when spinning. Is this normal? the machine has 55 hours on it and had a pump oil change about 10 hours ago. I'm going to change the impeller out so I...

OK, everybody knows this. I got lazy and did not run a hose or put it in the water. I figured I would run it about 30 seconds and shut it off. I needed to check something after a fix. So I fired up the engine, ran it at partial throttle and on shut down it gave a very unsatisfying glurg...

I have two problems. One, I cannot figure out how to remove the existing Bilge pump. Secondly, I can't find an OEM replacement. 1) I tried to remove my bilge pump but can't figure out how. Do I turn the big "wing nut" looking assembly at the top? So far, that will only move about 5 degrees...

I finally started taking apart my jet pump. The wear ring is shot and the impeller shows signs of abuse as well. I need to replace the impeller, a wear ring, and a couple of broken bolts (stator bolt being one of them sigh). I have a couple of questions based on my pictures below: 1. Is there...

Two months ago I put my boat on the water and after 5 minutes running the starboard engine just died and didn't want to start. I took it home, cleaned the air box, filter (which was really dirty) and started the boat-no problems. Next time i put it on the water same thing-the engine died after...

Good Morning, I have a few questions that I hope a tech or someone else could answer. I have a 1996 Challenger and believe the "Fuel Baffle" (P/N 204560071) is the reason I am not getting any fuel to the engine. I cannot find an actual "fuel pump" in any of the drawings. I noticed in a...

Hi Guys and Girls, I am new to boating and used my Sportster LE Boat for the 1st time today in the River Thames (UK). We had the bilge pump switched on nearly all the time! When we removed the boat from the river the water kept pouring out of the boat for ages!!!!! Is this normal...

The nipple is cracked off my oil pump so oil is just running out.. Do I need to buy the assembly or just housing? Does it come pretuned or do I need to mark where it comes off? thks!

I've got a 2011 GTS. around 350 hours. The splines are almost completely stripped on the impeller and the drive shaft. After I pulled the pump and shaft I noticed wear on the shaft and found it had been rubbing on the carbon ring. Is my engine way out of alignment or did the play caused by...

After starting up my 2001 GS on the trailer with water connected for less than a minute, I hear what I will describe as a "rattling/growling" noise that is much more perceptive from outside at back of the ski than from inside the engine compartment. If you kill it and let it set for a...

I've got some cavitation after a friend borrowed the jet ski and claimed he fell off of it into some weeds. I wasn't there so I don't know the whole story. I had replaced the wear ring ~6 months ago, still running the original impeller. When I took the pump off, this is what I found for the...

Hi all- Im new here; I hope I am doing this right and in the right section. I have a 97 GSX. I pulled the jetpump to do a rebuild. Got the new needle bearings etc... and the shaft will smoothly go through the rear bearing but not the other bearing. I thought it was maybe defective or...

Hi all, I have a 2002 GTX DI, It always had an annoying rattle sound on idle but went away when throttled was opened. This past weekend I got it out of the water and started it when I revved it up the loud rattle did not dissapear. It sounds like it it coming form the back so I assume the...

Hi everyone, A few weeks ago I ran my tank very close to empty. After refueling and taking the boat out a different day, there were some issues with it beeping if I idled for any length of time, and a studder / hesitation when raising the throttle just above idle. The problem slowly got...

What is the best solution for repairing a broken stud that holds the pump housing to the transum. When I was removing the housing, the stud simply brake in half as I thought that I was loosening the nut. I've never had this happen.

Hi All, I have a few questions about my jet pump. 1.) Is there a service out there to restore fiberglass hulls to the smooth finish they once had? I don't care much about looks, but a smoothed clear coat to cover all the scratches from beaching would be nice for my old girl. What would be...

Okay, I have done a lot of work on this boat today so I will be as concise as possible. Here is what I have done: rebuilt carbs, replaced all fuel lines, added an inline filter, rebuilt pump (new wear ring, impeller, bearings, thrust bearing/washer, seals), rebuilt drive shaft (carbon ring...

'96 GSX - Is there such thing as a replacement return spring for the oil pump? I can't seem to find one - just a replacement oil pump for $150+ Seems like an expensive way to get a spring... I guess I could switch over to premix, but with two GSX's, having one premix, one not... or switch them...