-
This site contains eBay affiliate links for which Sea-Doo Forum may be compensated.
RESTO Double trouble: 97 & 98 XP
- Thread starter DAGRE147
- Start date
- Status
Check the side of the Carb for pulse? Im pretty sure there is a plastic diaphragm in the mag side carb that pumps the fuel, it might be in wrong or something. trickle some gas in and see if its sucking. If not, then thats why she wont draw fuel. You didn't spray the check valves in there with carb cleaner did you? I think it might distort them.
Your so close!!
I had a problem with my 96 GTX losing prime. Cleaned carbs not much help. Instead of rebuilding, I found 2 almost new carbs on Ebay for $120 and just put them on. The rebuild kits are not much less and might not work. Fired it up and the bogging and loss of prime was gone. I must have went out riding 5 times adjusting the old carbs before I gave up. Next time I know what I will do. Might be the fastest fix after you rule out any tank or spark issues.
Last edited by a moderator:
Looks good! Yeah carts are the way to go.
Tossed together another cart this morning out of some wood I had laying around. Trying to get both skis on carts and get the trailer out the garage to free up some space and also start work on fixing the trailer. Didn't have any carpet so gonna use foam for a quick fix.
My wife would beat me if I dragged that into my living room!
Any headway on the fuel pump?
I can pull one of my carbs apart and send a pic if it would help you identify the problem.
Go get a silver tarp at Lowe's. They're nice and thick.
DAGRE147
New Member
I took off the fuel pump yesterday to make sure I rebuilt it correctly and also checked the fuel lines. Everything looked good, even the pulse had premix in it (assuming it's from the fuel I added manually). I removed the fuel filter I had on, even primed it with my mouth....I'm stumped
Unfortunately my house got hit with a stomach virus yesterday afternoon....cut my day short! Still recuperating so not much will get done today.
Side note: after I put the seat back on, it seems to be sitting a little high and the hood is hitting the seat when I try and close it. Do you have to compress the seat in order to get the outer boot on, thus keeping it slightly compressed and lower?
Racer, for now it's just gonna stay in the garage until I return from my upcoming deployment....I don't trust my wife lol but thanks for the good tip
Unfortunately my house got hit with a stomach virus yesterday afternoon....cut my day short! Still recuperating so not much will get done today.
Side note: after I put the seat back on, it seems to be sitting a little high and the hood is hitting the seat when I try and close it. Do you have to compress the seat in order to get the outer boot on, thus keeping it slightly compressed and lower?
Racer, for now it's just gonna stay in the garage until I return from my upcoming deployment....I don't trust my wife lol but thanks for the good tip
Pulse shouldn't have fuel in it at all. At least I have never seen one. I'm guessing its pulling it right through the valves. If that fuel pump was working, then you would be getting fuel to the carbs. The pulse is a negative pressure tug on the line, should be a light push/pull, it shouldn't pull fuel up into it. You gotta be careful about that too, because if it is puling fuel through the fuel pump into the pulse line that motor could run away on you and lean out and you wouldn't be able to shut it down.
I hear you about the stomach bug, I haven't gotten that yet, but I feel like train hit me today as well. Doesn't help that the wind chill here is -25.
I will post some pics of a fuel pump on and old set of carbs I got. Just as a comparison.
Im not sure I understand what you mean about the seat, but I dont believe you have to compress it, at least not much more than sitting on it.
So you might have made a common mistake of putting the plastic concave diaphragm on upside down. I snagged this pic from anothers post. The first pic you can see the concave section goes downward, its the little curved black line in the pic. Its easy to accidentally put it in back wards and it wont seal or pump.
The next pic is just a shot of the orientation of the check valves. I'm certain that if you get this pumping your ski will run.
The next pic is just a shot of the orientation of the check valves. I'm certain that if you get this pumping your ski will run.
Last edited by a moderator:
libertcat
New Member
Yes, sounds correct... But look, pulse is sealed off from the rest of the pump/carb by membrane and hard gasket (per your order, and pic attached), so how would gas get in there? If the membrane and gaskets are good, the only other way for gas to get inside the pulse would be through from engine trough pulse feed. I don't think this should happen if that's the case. I took apart few carbs, never saw gas in the pulse...
Loudoo96gtx
The Member Fromerly Known As GTX787
Love the stand I really need to build one how is the one you built do you think the wood would hold a 96 gtx?
Yes, they can hold a 4 stroke. Google twinturbomustang pwc bombproof stand. There is a pic of your cut list I think you need 6 or 7 2x4's, screws, 1/4 lag bolts and 4 4" casters. Total cost it's around $45 less carpet for the bunks.
Loudoo96gtx
The Member Fromerly Known As GTX787
Ok thank you so much I have been looking for a cheap stand to build and I think I found it.
Loudoo96gtx
The Member Fromerly Known As GTX787
? I don't know who Lou is my name is loui or short for Lou
Loudoo96gtx
The Member Fromerly Known As GTX787
Did I take someone's name that already on here can I change it I feel bad it said it wasn't takin when I signed up
- Status
Similar threads
- Locked
