removal

Hey there! Need some help... I'm stumped. I cannot seem to figure out how I can remove (then put back) the gas shock that's holding up the hood. Any advice would be great!! Please see picture. Why am I removing? I need to review fiberglass work that was done on the machine. It's been...

Hi guys! I just replaced my LCD on my 2004 Wake, when I plug the cluster back in it sits idle at 20 MPH and 3000 RPM, how can I "re-zero"/calibrate it back to sitting at zero where it should? Thanks in advance!

I have gotten the rubber boot off where the driveshaft connects to the PTO and I know some people say to remove the "c clip" when removing these driveshafts but I cannot find it anywhere. What am I missing? My driveshaft won't budge

Do any of you have any good resources for how to rebuild a 97 717 Gti carb? From removal from craft to rebuild to reinstall? Also what to purchase for rebuild. Much appreciated!!

I need to remove the starter motor from my 2004 GTI LE RFI It is the 110hp, fuel-injected, 787 RFI-engine, I think. I've tried to follow a procedure I found here, but it might not apply to my specific model. It mentioned removal of a black negative cable from the starter that I didn't have...

Hello everyone, I am new to the forum and I have a 1995 Seadoo GTX. I bought the ski 2 years ago from a guy who has owned it most of its life. He rebuilt the engine right before I bought it. The ski runs awesome with no issues until yesterday when i was on the water. I am pretty sure the...

I have a 99 challenger that has two motors that are flooded. One motor was bought earlier this year and has a no fault warranty. I'm in the process of taking the motor out and have hit a wall. Im new at all this and working off videos and forums. Im to the point where i need to get the exhaust...

I have a 2001 Utopia with Mercury 210 hp M2 Jet. I took the Nozzle Assembly and Stator off with little problems. But, while removing the bolts holding the the wear ring to the drive housing, I broke one of the long SS bolts (the one on the bottom right). It sticks out of the inner wear ring bolt...

Hi everyone. I was launching my '93 gtx when I noticed water rushing in. Lucky I never unhooked it from the trailer or it would be a goner. The drive shaft boot is torn. The motor end of the boot itself spins when the motor is turning which is why the boot tore. What do I need to do to fix this...

Hi everyone. I loaned my ski's to a cousin and one came back with a little slippage. Looks like the drive shaft splines have given out. Hopefully the flywheel female section is ok. I have pulled the pump off, removed the flywheel cover, clamps, and just by looking, I can't figure out...

This is all very new to me and I'm a Rookie so please be kind. I just picked up a 1994 Seadoo XP that had been sitting in a garage since 2006. The guy said he doesn’t think it was winterized before it was stored so I can only imagine what’s wrong with it. When I picked it up it we couldn’t even...

Hello, So I am pulling out my engine out of my ski and I almost got it out...I was wondering if anyone has any tips to make the removal easier. If you look at the attachment, I am on step 4.9(Using a 12mm socket, remove the two rear motor mount bolts. Slide the engine forward to clear the...

Ok, I'm also suffering from the old grey fuel lines. Thus far, I have changed out the fuel line, cleaned out the fuel selector valve, removed the old gas and cleaned out the tank, etc. This was enough to build up my confidence, so now I am going to go for the Carbs. I have a 1996 GSX...

I am restoring a 2000 SeaDoo Islandia and I need to get the seating backrests off the boat to get them reupholstered due to the fact that they are badly sun-faded and cracked. I can not find any way to get to the hardware inside the hull. Does anybody know how to get theses off?

I am removing my jet pump to replace my wear ring on my 96' GTI. to remove the pump from the hull i need to remove the bailer pickup tubes and the water inlet tubes. With what, and how do I do this? THe pickup tubes look like they are stuck into the fiber glass. seems hard to remove ..yet i am...