gsx

Hi everyone...I am having an issue with my gauge on my 2000 seadoo gsx rfi. Currently Ive been riding the ski with the gauge disconnected. When it is connected it displays "888" (like it's resetting or something) and everything is lit up on the gauge. It also stays lit up like that when the...

I acquired a 1996 gsx from uncle and it has sat for the last 3 years. Drained the old gas put fresh gas in and a new battery and she fired right up! The issue is there a very loud whining noise from the driveline/impeller maybe? Is there a grease fitting or a bearing or oil or something to...

[I apologize if this topic has been covered ad nauseum, but I tried searching on "96 GSX Dead Battery" and the search stripped out "96" and "GSX" because they are too short to be used as search terms and I ended up with 10+ pages of posts to slog through. I spent 20 minutes doing that and now...

Pulled the info gauge out of my 1996 GSX to try to get it to work after repairing the VTS system so I can tell the position. The picture below is what I discovered. When I bought the ski the gauge and VTS did not work. I purchased a repair kit but don't think that it is going to help my GSX...

Hi All, My first post here. I am in the process of rebuilding my engine after a big end conrod bearing failure.. It is the first time i have rebuilt an engine and i have learnt a lot from reading the manual and online etc. Finally the engine is on the mend again and i have just sealed the...

Info: got a great deal and bought a 1996 Seadoo GSX Bombardier (used, about 100 hours). Problem: everything works great except for the fact that when its in the water, it won't go past 3500 rpms. I have tried everything I could think of, but can't figure it out. Things I've Tried: we...

Hi guys, This post rolls on from my last thread where I couldn't get my GSX running. Now its had; a new ignition coil, 2 x carb repair kits plus 2 x new needle valves and seats & a solenoid. Its finally running. But when I try and start it, it will cough and splutter and not start...

Hi guys, I'm new to this forum and Seadoo PWCs. I have just bought my first ever seadoo ski, a 1996 GSX. (781cc) Its been converted to pre-mix, had an engine rebuild roughly 30 hours ago but been stood for 2 years since. It has a good spark and compression but when trying to turn it...

Hi everyone, I'm new to the forum, and looking for some technical help. We're attempting to sell my wife's '96 SeaDoo GSX, since we haven't used it in three summers, simply due to work, weather, etc (it was winterized, and stored indoors since then). 108 hours on the machine. Last week, I...

Hello all, I have a 1996 SeaDoo GSX. I recently purchased a set of rebuilt carburetors and replaced my current ones. I am looking to sell the ones I have just taken off, keep in mind that they will need to be cleaned and rebuilt. I am located in San Diego County, but I am willing to ship...

So took out the seadoos first time this year. Charged the batteries all winter winterized them. Ran them for about a hour or so no problems a all.Took them back into the marina to trailer them went to go get the truck came back and one won't start. Checked battery already, dash lights up but...

ello greekhulk riders! I've often googled and seen the site but never joined as never been too into the couches. So let me just jump into a little about me. Michigan. 26. Love any powersports. I buy and sell a lot of toys just to mix it up. When I was little we had mid 90's Polaris...

I need the info center for a 96 GSX Seadoo. I was replacing the LCD screen and when taking apart it was full of water! Totally rusted up. Will other years work? As long as it has the 787 engine...? I'm also new to this forum.

I need the info center for a 96 GSX Seadoo. I was replacing the LCD screen and when taking apart it was full of water! Totally rusted up. Will other years work? As long as it has the 787 engine...? I'm also new to this forum.

I'm looking for some input from Seadoo engine gurus to shed light on a failed engine. I recently purchased a 99 GSX RFI fixer upper pwc. I am not knew to PWCs but this is my first Sea-doo. I didn't water test prior to purchase due to a damaged impeller but engine started easily on the trailer...

After reading through numberous "water in hull" posts I decided to just make a post with pictures. I have a 96 GSX that runs great but brings a ton of water in while on the lake. The clamp closest to the carbon ring is lose about 1/4 inch (gap). How tight should that be, also the VTS boot is...

Hey guys so ive had this problem all last summer and still having it and im hoping someone has a solution. So my 97 gsx has like a hesitation when you pull the throttle in all the way. For example if i take a sharp turn and mash the throttle it will only go to about to 4800-5000 rpms and if i...

So i just got done rebuilding my jet pump, everything except the impeller and the shaft it screws onto. After i finished i spun the impeller and noticed that i grazes the wear ring in 1 maybe 2 spots up near the edge of the wear ring. You can feel the hesitation when it gets to that spot or...

Found this the other day and purchased one as for the price it's a steal (I'm from the UK & Only one place in the country sells this for just shy of £300/$425) So was a no-brainer for me to import it - I've never seen a GS or RX doo with a step on in this country (that means nothing though lol)...

hi guys glad i found this site just bought a 98 gsxl 951, are these kind of rear? anyway hope to get some info from this site not found much in aftermarket mpem for it yet tho reading reading reading :)