New profile posts

HEY I KNOW ITS BEEN AWHILE SINCE YOUR POST BUT DO YOU HAVE THE SPEEDO AND TACH FOR 787? 954-663-9871
TYLER THANKS
Hey 10forty2,

quick question I've been at the boat and hooking up that dual battery setup, can you remember how you wired the switch going from the stock switch to the blue sea one? I am seeing a red and black wire going to 1 post and another red wire going to the second post, just curious how you hooked up your Blue sea 4 post switch for the dual battery.

thanks in advanced
10forty2
10forty2
Howdy! Unfortunately, I haven't done the job yet. I have the kit and have looked it over, but have not installed it yet. At this point, I probably won't take the time to do it either, because I'm probably going to sell my Speedster. Nothing wrong with it, it just isn't my style of boat. I'm more of a center console fishing boat than a corvette on water. Second part of my reply on another message.
10forty2
10forty2
I had planned on replacing the OEM switch with the Blue Sea switch and connecting both batteries to it. I don't think there's any need to use the OEM switch in that configuration.
HEY RACER XXX WOULD YOU MIGHT KNOW WHERE I CAN FIND SOME GUAGES I HAVE AN XP AS WELL ITS A 97 I NEED A TACH AND A SPEED GUAGE.. PLS ANY INFO WOUL HELP THANK YOU
racerxxx
racerxxx
Check with minnetonka4me he's a member here dealing in used parts and will guarantee them to work. I have nothing for that hull style, sorry about that
XPSoFloRida86
XPSoFloRida86
THANKS FOR THE RESPONSE RACERX.
Hey guys I'm looking for some recommendations on my project:
2007 Sea-Doo wake 215-flywheel bolts sheered off.
Replacement parts list:
Arp flywheel bolts
Magneto/stator (OK to buy used??)
Crankshaft thrust washer set
Gasket kit
Main bearing set
Rocker arm/head bolts
Should the timing chain be replaced? Doesn't appear damaged
Anything to know that the service manual doesn't tell you?
Add or subtract anything?
seadoosnipe
seadoosnipe
Yeah, I would. And yes, if you were under tow, you should pinch off your water inlet from the pump. I believe the manual says less than 5 mph, your good, but over that, you'll fill the exhaust system with water, till it dumps over into your exhaust ports. Sounds like you got a handle on it. Your description, your resolution, sounds great. I would also want to know the root cause, don't want to replace parts again.
WakeProject
WakeProject
Apparently seadoo was still using the old style flywheel bolts in 2007, I believe that was the problem, they backed out, pushed into the magneto and sheered off. Everything else looks so good I considered replacing the necessary bolts and putting it back together. I've since decided to rebuild with new parts, I'll post pics, would love to get some opinions.
WakeProject
WakeProject
Unfortunately, I don't see a way to post pictures. Seadoosnipe, you said replace timing chain and gears which is what I'm planning to do but have a question. It looks like the 2 gears on the crankshaft are pressed on, can those be replaced?
Hello, I have 2 XP DI's I just picked up. I read that you can suppy/sell the Candoo Pro? Do you have any used ones?
What do they cost? thanks for your time... Mike
Good evening everyone. Noob here to this forum and jet skis, just bought my first one. 96 Sea-Doo sp. Been sitting outside rotting for 3 years or so. I think I’m hooked and haven’t had it in the water yet. Lol
seadoosnipe
seadoosnipe
very addictive my friend. First thing you'll want to do, check that all the cables are free. Second, get a battery on it, then pop off the spark plug wire, and check it for spark. IF you have spark, then it's def worth working on. Good luck!
just acquired a 1995 gtx sea doo, been setting for years with very low hours. flushed fuel tank, oil tank was filled. After got it running then applied water to fitting. ran for a while then started popping the 5 amp fuse. Applied a new ground cable to the block and fuse popped again, unplugged stater plug, fuse never popped. any help ?
seadoosnipe
seadoosnipe
Did you jump this ski off with another vehicle that was running? When you jump off these skis with another vehicle, it can't be running. A alternator puts out 14 volts, a car that isn't running, puts out around 12. If you jumped with that car running, you fed power backward through the MPEM backward, causing it to blow that 5 amp fuse. There is a diode in that MPEM, that if I'm remembering right, is now bad.
Hey nice build. I was just curious if you had the cut files for the carbon fiber ignition plate? I want to do the same with mine just wit red. Cheers
Hey, good to see you got that dioded ski out on the water, after that tedious fix it must have felt good. Just got through the second tank on my GTX, running very strong, I hit 58 at one point this past weekend. Feels great to bring something back from total junk to a glorious time on the water. When not riding, I'm turning my attention to the 96' GSX, it's a total mess.
cj3737
cj3737
It feels great.. cant believe its runs as well as it does... 20 years old and pretty much show room condition.

Im still in rebuild on the gs in pieces... slowly going back together. I have a good feeling itll run so I can sell it off.. been a pain.. the gts is going now too.. running a bit lean so I'm gonna rebuild carbs and all the housing. Think I may sell both gs and gts... keep the gsi
My brand new 2017 seadoo gts 130 leaks salt water ,
Was leaking through hull screws that hold front hatch on , sealed them up .
Still takes on 150ml salt water every use. Salt spots all over the motor .
There is two small tracks, one on each side of the hull where the seat cover sits, water will come in here but is it a vent for air as well? I feel some serious design flaw or manufacturing carelessness , help !
can someone call me that has experience with 96 speedster twin rotax engines and propulsion 419-250-3352 troy need guidance please please
T
troylindsay1147
thru hull fitting and drive shaft cover sleeve questions???? please help me
T
troylindsay1147
the cover sleeve is white plastic and is kinda long. not sure where to get them or how they attach??? or function if mine are busted off??
Having issues with my 2000 sea doo gtx. Has carbs and when out of water with hose hooked up seems to run fine plenty of rpms. Once i put it in the water seems to me that it will run great for 30 seconds and then seems to miss and bog down, running 4600 rpm at best 30 mph and that is a struggle. Replaced plugs coils and removed fuel tank to clean and put fresh fuel in it. Any help is welcomed!!
no oil pressure on a 2010 gtx260 looking for fee back on what it may be .new filter and oil.also a new pressure switch installed
Just bought a 2009 RXT-X....came with a miss...replaced plugs,coils and injectors...seem to run great....put it in the water and no miss but doesn't want to go over 45 mph. Pulled it out of the water and I have 4 " of water in the hull and the 12V light and code on....Looking for some help where to start...Thx
I have a 01 islandia with the 240 m2. I've only had it out once in two years. I went to pull it out and get it on lake. Naturally the gas went bad. I emptied tank and replaced filters. It still will not idle. It starts and wants to go to idle and dies. Im looking for some advice. Thx
Quick question,Is this 180 a fairly reliable, good performing boater did I make a poor decision purchasing.
Many thanks for your reply,
The light and alarm come on only after the engine runs for about 10 minutes.As mentioned the oil pressure sensor has been replaced.I will check other suggestions as listed.Thanks again for your reply.
hello I have a 2003 Seadoo GTX DI and it stopped peeing. my assumption is it is clogged because a friend used it at my lake and came in close to shore and didn't cut it off a few times. my question is can i take an air compressor with a spay nozzle and spray compressed air in the pee hole haha to clean it out? or whats the best way to clean it out? before i start taking it apart to check for clogging. thanks
I bought a 2001 Challenger, very clean boat, all the inside has been redone...The first day, the left engine kept stalling...took it to the mechanic that works on ou
r jet skis...@$2300 later we put it in the water and ran pretty well for a full day. Tried to get on the lake today and the left engine won't even start. Is there a trick to running these boats because other than replacing the motor...my mechanic tested
Top