oil

Hey I'm working on a mates 98 xp engine type 947 and just came across something I'm not to sure about. The oil light just came on but it the ski runs pre mix. He bought the ski off a guy that gave him no info about the ski. It still has the oil tank in the front with the sensor still...

I have a 95 seadoo xp that started bogging out on me when i first bought it 3 months ago. sat for about 2 weeks after every ride this summer. Had trouble getting it to start and it always took about 5 or 6 times to get it cranked. So then I decided to get my carbs cleaned. after, the guy didnt...

Hey guys I did a quick search but didn't see anything here so sorry if this is in wrong place. I'm trying to find an oil filter for my 2015 gti 155 limited. I see k&n makes some but they only have up to 2014 in their list. I'm sure I can go to dealer but they are a good 30 min or so away and was...

I have a 1997 Seadoo GTX and I just rebuilt the carb and replaced the original fuel lines. I started the ski for the first time and while it fired right up there is oil coming out of the exhaust, actually quite a bit. Is this a rave valve issue or top end rebuild?

I got my ski running great now after a mess with a carb rebuild, I had one of the little hinge pins from the needle arm not correctly in its slot and it was causing a leak. It's just A Bit rich on oil though. When you set the oil pump lines, where should the throttle position be? I set the lines...

Finally, after 7 years of paying an arm and a leg for yearly oil changes on my 2008 Speedster 150 (4-stroke Rotax), I decided to do it myself: got all the needed equipment, except the manual calls fro 10W40, but the only closest oil I could find at the nearest (10 miles) West Marine is Pennzoil...

I have a 96 gtx that appears to be leaking oil from around the grommet on TOP of the tank. The leak appears to be coming from around the sender unit for oil level readings. The sender is very loosely fitted in the tank. Is that how it is supposed to be or should it be quite tight. Also where is...

Short story, this engine let go about 30 minutes into the break in period..is there a way to tell if this was caused by a too lean condition or lack of oil?

This is my first post other than my introduction in Meet and Greet. I was recently given a 1996 Challenger that had a corroded engine but got that replaced so it's brand new (2 days old). We've had the boat out only once but love it. I have a few questions that seem stupid but I don't know...

Hey guys: I have a 2004 Utopia with a Mercury Optimax M2 200 DFI 2.5L Engine ( SN# 0E415782, Model No: S200J20AS ). At the end of last year I changed all the filters I could including fuel and oil. I changed the inline oil filter, Mercury PN# 875284. I'm just about to fire it up for the...

Hello guys! Dr Honda, might be your area, but if anyone else knows.... Last spring I was changing the gear and stator oil before storage. When I went to change the stator oil, I was going to do it simply be removing the fill and drain plugs, sucking out the old and replacing with new. Upon...

Hi, I have a 1996 Seadoo GTX Rotax, There is two black covers just behind the spark plugs with a little red circle on top(I have attached photo), 1 is in real good condition(right one) and the other the rubber inside is broken(left one), Can I just leave it off? and if I need it on, what are...

Hey everyone, Hope you guys are having a great new year. I am having an issue with my '09 wakepro. There appears to be an oil leak, when the jetski is running and it looks to be towards the rear of the craft. I did quiet a bit of reading and research and the consensus points toward a bad...

Hi all, I am new to this forum, I am having an OIL Alarm issue. I own a GTX 155 2008, last weekend after running fine (at 50-70 kmh) for 20 mins*OIL*sign poped up and had a continous long beep. Turned off the engine right away and gave it a try once again and engine started and sounded...

Two months ago I put my boat on the water and after 5 minutes running the starboard engine just died and didn't want to start. I took it home, cleaned the air box, filter (which was really dirty) and started the boat-no problems. Next time i put it on the water same thing-the engine died after...

Hey guys. I am in need or some more help. I stripped down the motor and whatnot for rebuilding purposes but before I put the RV cover and carbs back on, I would like to test my oil injection to make sure it's working properly. Is there a standard way I should do this? Have any of you all...

Anyone have a list of the oil and water line sizes and quanty , and which type of tubing to get to replace them 94 GTS and 96 GTI...Thanks again guys

Hello All, I have a 2002 GTI LE into which I'm swapping a new SBT 717, but I'm a bit worried about the rotary valve cover. It isn't gouged or grooved anywhere, and the surface seems relatively smooth, but it seems to be wearing unevenly. Looking at the outside edge, the surface appears worn...

ok so as i was putting my carb back on and connecting the cables i noticed on the cable that is connected from the thottle cable mount to the mount on the oil injector wont spring back. so if you hook it up, pull the throttle wide open the arm swings like it should to wide open and would be...

The nipple is cracked off my oil pump so oil is just running out.. Do I need to buy the assembly or just housing? Does it come pretuned or do I need to mark where it comes off? thks!