impeller

Upon inspection of the underside of my newly purchased 2007 Speedster 150 SC, I noticed the intake grate was broken. I inspected the impeller and surrounding areas, and I cannot see any damage, except for a red mark on the back of the impeller. I suspect it was a ski rope getting sucked up...

I pulled the jetpump on my 98 GTXL to rebuild with new bearings, seal and wear ring but I was surprised to see that it had a solid brass wear ring. Is this OEM?? Is it okay to install a plastic wear ring in place of the brass one? The impeller was beat as well so I need to replace that. Any...

This 99 SPX came with the lakehouse I recently bought, obviously the previous owner did not take care of it and it appeared it had been left in water for quite some time. I have cleaned and put new gaskets on carbs, drained the oil and gas tanks and put in fresh. Don't ask why guess cause I am...

I have a Sea Doo Challenger with a single 215 hp engine. My son is 175 lbs and likes to slalom ski, but I have difficulty pulling him up. What is the best impeller I can buy that would make it easier to pull him out of the water?

I have a 97 sea doo xp and my rebuilt engine is about to come in next week. I need to break it in before i can go full throttle but to break it in i need to at least roughly adjust my cleaned carbs. can someone tell me what i need to do to tune my carbs with out the engine running so that i can...

I have a 07 se gti 155. I have the shop manual and can not find how to grease the impeller for a yearly maintenance. Is there a fitting that I just put a grease gun too? What else do I need to grease back there? Thanks, Your help appreciated. Tony

My 92 stock impeller was a 13/18 and the new one is a 14/19 solas. Will this affect the cooling of the engine? It has more take-off speed I cant tell about top end. I was just concerned about cooling.

I just bought a 2004 Seadoo 4-Tec sportster. Had it out 4 times. The second time, it would rev high, but only go 10 mph. Got it out of the water, filled it up with gas and some seafoam, went back to the lake, and it worked fine. Worked fine the 3rd time out. 4th time, worked fine most of the...

I own a 1996 SeaDoo XP and it has bad cavitation when i turn and do a broadie and when i am at a stand still. I did some research and came to the conclusion that it was my wear ring. So i starting taking it apart and got the nozzle off and was looking around and the bronze part was cracked and...

I had a rope cought around the shaft but not ant further... the jetski ran perfect for a half and hour and now jetski doesnt have any pick up. It sounds like it is running ok, but just now pick up. What is most likely my problem, and how expensive to fix???

All the sudden I hear the bottom of the boat scrape the bottom of the lake as it dropped from 4ft to 1ft and a rock was sucked up and damaged the impeller. Just ordered new impeller and wear ring ...$368 later... I want to try and install it myself... ANY TIPS or instructions??

Here's the ideal combination of tools to change your impeller... an old hitch drawbar (minus the ball), a 1/2" drive breakover bar, a 1/2" drive 12mm socket, and a piece of 12mm allen wrench (cut off 2 inches long with a dremel and cutoff wheel), and the impeller change tool. Have a...

Ok I've searched these forums and read and read for almost 2 hours now... what is the stock impeller pitch for a 2006 RXT 215hp? What would be a good aftermarket performance impeller pitch for it? I'd like to put a Solas impeller in (nice and shiney!), but don't want to kill the top-end and...

whats up everybody? i got my 95 xp running and this thing will fly! i know i need a new wear ring and im going to order a OEM one and im gonna go ahead and get a new prop while im at it. my only question is do i buy a OEM prop or a Solas, and if so what pitch? thanks alot!

I need to replace my old impeller which was siezed and had to be torched out. See my other threads I also need the impeller shaft and housing. I have the cone reservoir and HAD the bearings until the package was stolen from my doorstep.... Thanks for your help!! :seeya:

Wondering Everyones opinion on these three parts. Finally got the impeller and stator and wear ring off. I really want to do the jb weld trick on the wear ring but my fear is its to far gone. Anyone seen one this bad and JB weld work. Also as far as the impeller and stator go. Is it...

I have realized that the person I bought the boat from really didn't care to much about the boat. I have been looking and it needs a intake grate, impeller, wear ring, stator and possibly a ride plate and a tilt plate. This is for a 2000 speedster with the 240 Merc. Doing my research there...

First off i am like stated in other posts I am some what new. I just bought this boat two weeks ago so I don't have much experience. I have looked below when i bought it and it looks pretty torn up. I know i need a new intake grate but what i am wondering is if i should get a new impeller and...

So here's the deal: got a 155 mm stainless sleeved wear ring with a 159 mm impeller for my rxp-x. One option, get the smaller impeller to fit the wear ring, as it's already in, or fight to get the right wear ring, and use the 159 mm impeller. Also, should I stick with the 15/21 I bought, or opt...

I sucked up a ski rope from an inner tube into the starboard side impeller. I can feel the rope inside, HOW THE HELL TO I GET IT OUT? Can anyone help me? DO you think I'll need a new impeller and housing??? Please respond and thanks for the advice in advance. Tvardaky