Search results

Hi guys I built a limited race boat. Made it through the first round of racing got home and blew it up. Put a fresh rebuilt engine in and supposed to race this Friday. Tried it yesterday and the pipe stays cool but the ADA head gets super hot. The plugs were almost to hot to unscrew by hand. I’m...

I built a limited class boat over the winter and went to fire it up today. I put the key on and only get one beep. I opened up the grey box and the msd is not lighting up. Any tips or advice? Thank you.

I bought a set of used oem cylinders with new sleeves off eBay. Got it all assembled squish was off so disassembled to put different base gasket in. Upon removing cylinder found this crack. How could that happen? Is that maybe why the case was painted over? Cover it up?

I need an ECWI controller for a spec 2 anyone have anything? PayPal ready. Thank you

Hi guys very green but in the process of learning how to build my first limited race boat(96XP). I am trying to figure out what jets to use when I rebuild my 46mm red top(mikuni) carbs. Here is a list of parts that will be used with the carbs if this helps: odyssey head with 43mm domes, spec 2...

My rave bellows collapse every ride. Any ideas why. Here’s a picture. Thank you

I was having a problem with my raves leaking very badly. I bought new housings, bellows, gaskets, orings and springs. Now they just collapse on themselves after a ride. Any ideas?

96 xp and the raves constantly leak. I’ve replaced the gaskets and orings every year when I clean them. They never stop leaking

I am going to attempt to build my first race boat this winter. A friend has some novi 44s. Will these work alright on a stock boat for the time being? What would I need to change to be able to use them? Any info is appreciated thank you guys!

Hey guys my XP starts so hard every time I go to use it. I have been through the entire ignition system and put in all oem parts. The only thing I have never messed with is the rotary valve clearance. How do I go about checking clearance? Do I just remove carbs or do I need to pull the entire...

Went to ride yesterday ski started right up on the ramp. Pushed it in the water running. The nose got hung up on ramp from trying to idle forward. I shut the machine off pushed away from dock went to start it again and it wanted to keep cranking even after letting off the button so I pulled...

I am stumped. I’ve been going at this RXDI for over a month now. You can look back at some of my previous post to see all that was going on. But long story short. I changed fuel pump and socks and filter. Start it up goes to .27psi on key on. Takes awhile to crank up towards 90psi to fire. It...

So I posted a week or two ago about fluctuating rpm and only 40mph at 6800rpm. Since then I have put in OEM rectifier, new wear ring and pulled the fuel neck off drained old fuel and put fresh in(unsure state of original fuel). Took to dealer and had BUDS hooked up. Only code was multiple 12v...

Hi everyone, I just purchased a 02RXDI last week from a repair shop out of state. The guy put it in a test tank before purchase and it seemed all there. Bring it home and back it in the water on trailer and let it warm up. Rev it a couple times and got 7200rpm like manual states. Take it off and...

Getting my 96 xp unwinterized to ride on Christmas Day. I had it start twice then noticed my plugs were not in tight and it started spitting oil. Tightened them down and started it again. Started fine and as I went to give it some throttle to clean the oil out of the crank(leaky crank seal) it...

I bought this project last week. I tested the ignition system per the manual specs. The only thing that did not test good was the ignition coil. I swapped the coil out of my good 96xp and still had no spark. I then swapped everything back and pulled the stator cover off and found it to be all...

Hey guys I got the flywheel issue solved on my XP and it’s running good.so went out on Halloween and picked up a winter project(or so I thought) driveshaft spun by hand so I picked it up for $300 with a trailer. Put my agm battery in and it cranked over good. Tested compression it’s 148 on both...

Hi guys lost spark the other week on my 96 XP. Pulled the stator cover to discover the mag cover only had 3 out of the 6 bolts in it. Sheared those three bolt heads right off leaving my stator, and mag cup ruined. Pulled the flywheel to install a new one and it sheared the woodruff key as well...

I’m trying to get the carbon seal apart on this gsxL I just picked up. The pump is still bolted on but the shaft is still sliding backwards when I pry back on the “top hat” that the circlip is under. Any tips or tricks to get the top hat to slide backwards far enough to pop the circlip?

I am looking at buying an 02 GTX DI with 125 hours on it. I know it’s likely close to rebuild time at 150 but the price is right so I’m considering it. The only problem is the owner says when he starts it it takes off up to 45 but if he hits a wave it cuts down to only 25mph at full throttle...