Search results

Any chance you could machine me one? Can we get in contact?

Yes the motor was run out of the water quite a lot but never more than 15 seconds without a hose bib as I was trying to diagnose a charging issue. There was one time my dad shut the ski off while I went to turn the hose off but I started it up after to make sure water didnt sit in the cylinder...

Thanks for the advice, The pistons before run time already had that on them. Maybe hard to tell from the photo but they do have those black specs. Sleeves did not have those spots black spec spots of course. Do you happen to like any pistons in particular and rings? Ill change the oil, back...

I am running "AMSOIL HP Marine® 100% Synthetic 2-Stroke Oil" I am confident the pump was adjusted correctly, I had it on the richer setting for break in. Yes, I did have the rubber intake covers on. But on afterthought, I know what the issue was my fire extinguisher had come lose from where I...

Hi, I rebuilt a 951 DI in 02 RXDI last summer it ran fine. I discovered i had an exhaust leak so I pulled off the whole exhaust and I just decided to take a look inside the cylinder and I saw the piston was scoured I have since pulled the engine and got it apart ill link the photos. I am a...

Hello, I got my 951DI rebuilt engine has 3 hours on it runs like a champ in the water full rpm run out etc, I pulled the plugs they were really black almost fouled maybe, so I decided to pull the raves too to look at the pistons and I found they have wear as shown in the pictures is this normal?

Hello, I rebuilt the engine over the winter for my 2002 Seadoo RXDI and it has a maint light (good to note it appears 10 seconds after start). I haven't been able to get my hands on a buds or candoopro system for months now so I've just been tinkering around. The question is about the knock...

Maybe I'm overlooking something in the post but the starter? No compression is created with an open head so when a weak starter tries to turn over upwards of 120psi of compression it could struggle.

Visit: SeaDoo Manuals - FREE PDF Download! And then on the left side, there is all the years select yours and then go on to your model's shop manual.

Hello, just did a fresh set of reads, Before start: 12.74 Running (At idle): 13.04 After shutoff: 12.64

Hello, Thanks in advance for your time and knowledge! I have a 02' RXDI that I just rebuilt new crank new everything quite literally. I started it up for the first time it ran good 1560 rpms then started to drop all the way to 1400 and then it bounces around above 1400. Maint signage on the...

Hello, I purchased a 2000 Seadoo RXDI cylinder head for my 2002 model machine 951DI engine. The fuel rail doesn't align perfectly the 2 screws that go in thru the top are off by so little I don't even know if you can measure that. I know the 2000 model had those bigger "fatter" air injectors...

You got any recommendations for a shop?

Okay, thanks. Just one last question, should I be ok to fire up the engine after the rebuild. Or do I need to send off all the injectors?

Okay, sorry for the misunderstanding! I cleaned up the raves they had a lot of crap on them but I got it pretty good, the little chip on the rave shouldn’t be a problem right? I’ve never heard people say it is. Also just to note I’m gonna be using amsoil instead of XPS. Better price and atleast...

Sorry, I don’t really understand what you mean. If this helps any, the sleeves are new and were bored to the correct measurements at a machine shop, new pistons and rings of course.

Hello, I’m in the process of rebuilding a 951DI I’m pretty close to dropping the motor in. I was thinking about what even caused this mess in the first place and I thought to look at the power valves and old piston. Judging off the pics would you say the power valve cuaght the piston ring...

I honestly don't know the issue. I think the crank is bent. The eBay seller wants the crank back. If it wasn't the case I would have got it rebuilt and sold it.

Hello, I have a damaged 951DI case, the bearing area has a ding in it pretty much look at the picture. I feel like it shouldn’t matter since the bearing dosent spin inside right?

Update - The crankshaft was indeed the issue. Takeaway, a brand-new WSM crankshaft cannot be trusted!