Search:

I have a couple AQ-30's which work great. I take the wheels off and replace with boards to use at the beach for overnight duty.

Spelling is far from any of my strong suits too. :thumbsup:

Did you get the Liberal arts because you did collages or because you went to college??? hehehehe

I will second BMANN06.

If you are bored with the new skis and not getting wet enough, there is always this :) http://www.youtube.com/embed/Cd6C1vIyQ3w

You are correct with the sound. I found playing with the trim at all rpms changes the sound, even idling out of the harbor. As far as the vibrations I won't worry about it. Rotax has made a lot of...

I've use an ultrasonic cleaner for years. I have a commercial machine used for the dental industry. I found the best cleaner so far has been DC-99. It's made locally by Davis chemical company. A word...

Generally your looking for 10-15% tongue weight of overall trailer weight.

Out of over 50 toys between sleds and ski's that have had rotax motors I can say I have never replaced one yet. They are pretty bulletproof. I would check the exhaust bushing other then that just...

Make sure your cranking the motor over while spraying. Don't spray it then try to start it. I've had to replace crank seals before when the kids got over zealous on one of my sleds. WD40 or fogging...

[QUOTE=Dr Honda;193289]Give it a shot of starter fluid.

I can't believe you said that! lmao I just spray premix in the spark plug holes or down the carbs if the airbox is off.

I've had better luck running lower spring tensions on both my 720 as Dr. mentioned. I'm actually running them @ 28 psi. The higher stock setting are too finicky in the transition form idle to mid...

More then likely the lines will be fine though I would pull the carbs and go through them.

I think a lot of people that buy just lose interest after the novelty wears off. I bought a new GT! SE in april and have 148hrs on it and have a little over 50 hrs on each of my 4 other xp's. The...

Check with a shop in your area that cleans injectors. I've had all 4 cleaned in my sled for 75.00 and it came with a flow sheet for each one.

Everyone needs to take a deeeeeep breath, Hmmmmmmmmmmmm feel better now? lmao. This forum is no different then any other. You see the same thing on all of them. Totally Yamaha sled forum is about the...

I don't own a seadoo boat though with the jet ski I don't use reverse. I just wait for 5-10' waves on lake michigan and ride with them. When you get up on top of them you just punch it down the back...

That depends on how much gas. If the weather is going to be -0 or lower I add a gal of gas to 15 gal of diesel in my VW diesels. That way if fires right up just like summertime since I'm too lazy to...

I've been researching them also. Here's some info on them http://www.youtube.com/watch?v=zNexwmOCf24

Do as you wish, it's not only the liquid that affects it but the fumes which are constant. Good luck.

You won't see it melt if thats what you're looking for. It becomes brittle and will crack or shatter with time. I'm a plumber/pipefittter and installed chemical piping all the time. I've see the...

PVC pipe is not rated for gas and will fail. You need to use MDHP,HDPE or similar material.

Opening later will give better low end torque and MPG.

They make new covers for rave valves that have alum. arms that link the valves together if you want to physically watch them open. I never really cared for them as I always set my motor base lines on...

I don't have experience with the 800's but on the old 670 sled engines we always ran thicker base gaskets to raise the port timing. Yes it dropped the compression but we gained rpm,torque and HP.